Real Carbon Fiber Front Bumper Corner Trim for Model Y Juniper / Model 3 Highland

$177.65 USD

Sale Sold out

Shipping calculated at checkout.

Real Carbon Fiber Front Bumper Corner Trim for Model Y Juniper & Model 3 Highland

Add a genuine carbon-fiber accent to the lower front bumper while giving the exposed corner areas an additional protective layer against everyday scuffs and light surface contact. Designed for refreshed Tesla body styles and installed using pre-applied 3M tape plus existing factory mounting points.

Real Carbon Fiber · Glossy / Matte · 2PCS · No-Drill Installation

🧵 Real Carbon Fiber

Made from genuine carbon fiber rather than printed or hydro-dipped ABS, with your choice of glossy or matte clear finish.

🛡 Added Corner Protection

Adds a protective outer layer over the exposed front bumper corners to help reduce minor scuffs and surface marks from everyday use.

🔩 Factory-Point Installation

Uses pre-applied 3M tape together with existing factory plastic mounting points and the included screws.

✂️ No Drilling or Cutting

No drilling, cutting or bumper removal is required when installed on the compatible vehicle configuration.

Carbon Fiber Styling with Practical Coverage

Enhances the Lower Front Bumper
The left and right corner pieces add a visible carbon-fiber accent to the refreshed front bumper without replacing the full bumper assembly.

Covers High-Exposure Corner Areas
The trim sits over areas that can be exposed to light parking scrapes, shoe contact during cleaning and other minor everyday surface contact.

Reversible Exterior Upgrade
Because installation uses adhesive and existing mounting locations, the part can be removed later without drilling new holes into the bumper.

Choose Your Carbon Fiber Finish

Finish	Appearance
Glossy Carbon Fiber	Deeper reflective finish that highlights the carbon-fiber weave
Matte Carbon Fiber	Lower-sheen finish for a more understated carbon-fiber appearance

Material & Construction

Attribute	Supplier Specification
Material	Real Carbon Fiber
Finish Options	Glossy Carbon Fiber / Matte Carbon Fiber
Surface Finish	UV-Resistant Clear Finish
Installation	Pre-Applied 3M Tape + Factory Mounting Points

Vehicle Compatibility

Vehicle	Fitment
Model Y Juniper Premium	2025+
Model YL	2026+
Model 3 Highland	2024+
Model 3 Performance	2025+
Model Y Performance	2025+

⚠️ Refreshed Models Only

This trim does not fit Model Y 2020–2024 or Model 3 2017–2023. The front bumper geometry is different on those earlier vehicles.

⚠️ Cosmetic Protection — Not Impact Protection

The carbon-fiber trim adds an outer protective layer that may help reduce minor scuffs and surface marks. It is not a crash protector, structural bumper reinforcement or substitute for careful driving.

No-Drill Installation

Pre-Applied 3M Tape
Each trim piece arrives with adhesive already applied to the contact areas.

Factory Mounting Points
The included screws secure into the vehicle's existing plastic mounting locations rather than newly drilled holes.

No Bumper Removal
The supplier states that the installation does not require cutting or removal of the front bumper.

Installation Overview

1. Clean & Dry the Surface
Clean the left and right front bumper corner areas thoroughly and make sure the mounting surface is completely dry.

2. Test-Fit Each Trim Piece
Place the trim against the corresponding bumper corner before removing the adhesive liner and confirm the contour and mounting-hole alignment.

3. Remove the 3M Tape Backing
Peel away the protective liner from the pre-applied adhesive.

4. Align & Press the Trim
Position the carbon-fiber trim carefully and press firmly across the bonded areas.

5. Align the Factory Mounting Points
Make sure the trim holes align correctly with the existing plastic mounting locations.

6. Install the Included Screws
Secure the trim using the supplied screws. Do not drill additional holes.

Typical Installation Time

Tesery states that most owners complete installation in approximately 15–20 minutes. Actual installation time can vary depending on preparation and vehicle condition.

⚠️ Allow Adhesive Time to Set

Tesery recommends waiting approximately 24 hours after installation before using a high-pressure car wash. Avoid disturbing the trim while the adhesive is setting.

Specifications

Attribute	Details
Product Type	Front Bumper Corner Trim
Material	Real Carbon Fiber
Finish	Glossy Carbon Fiber / Matte Carbon Fiber
Position	Front Bumper Corners — Left + Right
Installation	Pre-Applied 3M Tape + Factory Mounting Points
Drilling	Not Required
Quantity	2 Trim Pieces

Package Includes

2 × Real Carbon Fiber Front Bumper Corner Trim Pieces — Left + Right
8 × Mounting Screws
Pre-Applied 3M Tape on the trim pieces

Quick Answers

Is this real carbon fiber?

Yes. Tesery specifies genuine carbon fiber rather than ABS with a printed or hydro-dipped carbon pattern.

What finishes are available?

The current product selector offers Glossy Carbon Fiber and Matte Carbon Fiber.

Does it fit Model Y Juniper?

Yes. Tesery currently lists Model Y Juniper Premium 2025+ as compatible.

Does it fit Model YL?

Yes. The current Tesery selector lists Model YL 2026+.

Does it fit Model 3 Highland?

Yes. Tesery currently lists Model 3 Highland 2024+ as compatible.

Does it fit older Model 3 or Model Y vehicles?

No. Tesery specifically states that it does not fit Model Y 2020–2024 or Model 3 2017–2023.

Do I need to drill holes?

No. Installation uses pre-applied 3M tape and existing factory plastic mounting points with the included screws.

Do I need to remove the bumper?

No. Tesery states that bumper removal is not required.

How many pieces are included?

The package includes two bumper corner trim pieces, one for each side, plus eight mounting screws.

Does it provide impact protection?

It adds a protective outer layer that may help with minor surface scuffs and scrapes, but it is not structural bumper reinforcement or collision protection.

Applicable Model & Year Model Y Juniper 2025+ Model YL 2026+ Model 3 Highland 2024+